<-- back to Brakes#27226.jpg

A brake booster was first fitted to Datsun 1200 starting in October 1989. The Datsun 1200 is so light it does not take much leg pressure to stop. The booster means that less exertion is needed by the driver to press the pedal. The booster doesn't make the brakes stop quicker, but instead lets a small person press as hard as a muscleman.

Overview

#G15 Booster system was fitted to JDM 1200 1990-1994, Bakkie 1986-2008, and LHD 1200 1986-up

Album 16857

JDM from 1989.10 LHD from 1986 South Africa from 1986

1987 Nissan 1200 truck

Post 489658

The booster uses this large single-reservoir Brake master cylinder, which uniquely has two horizontally aligned bolt holes. Other Datsun 1200 master cylinder have two bolts in vertical alignment. It has separate front & rear brakes though sharing a common fluid reservoir.

Album 17265

Nissan 1400

Booster was used in South Africa B140 pickup starting in 1986.

Album 26700 Album 26703

Album 26701 Album 26702

It uses a similarly looking, but a different part number, master cylinder from the Japan-assembled pickup.

1980-2008 master cylinder NABCO type two-bolt horizontal mount 20.64 mm

http://datsun1200.com/uploads/photos/31349.jpgAlbum 31349 http://datsun1200.com/uploads/photos/31350.jpgAlbum 31350

PB110 Booster

The PB110 1400 used what appear to be the same small-diameter B210 Brake Booster (M45 Master-Vac with 4.5 inch vacuum diaphragm). But likely there are small differences as they have different part numbers.

http://datsun1200.com/uploads/photos/30544.jpgAlbum 30544 Post 498203

MASTER VAC 47210-H2601 MASTER VAC ASS'Y GL,GL (op.) DX 47211-26701 SPACER-master vac * same spacer used by 610, 710

DX came standard with non-power brakes, and needed a 2-bolt to 4-bolt adapter plate instead of the spacer.

Testing

Compared to a non-booster setup, the booster type will allows feel spongier. Even so, when the brake system is bled properly a booster type will feel fine (like any brake booster equipped car).

One simple test you can do is: Run engine for 60 seconds to build normal vacuum. Then turn engine OFF, pump the brakes until the booster loses vacuum. The pedal should get higher and tighter with each pump. All sponginess should go away after four pumps or so -- which indicates the brake hydraulics are OK. If it doesn't remove all sponginess, re-bleed the brakes. If the pedal travel does not change with the first few pumps (pedal does not get higher) then the booster is bad.

Vacuum Test

With engine OFF, pump the brake pedal until it gets high and tight. The press and hold the pedal down while starting the engine. The pedal should move down slightly. If there is no change to the pedal height, something is wrong in the vacuum circuit.

Leak Test

Engine RUNNING, press and hold down brake pedal. Turn engine OFF. Keep pressure on it for 30 seconds. The pedal should stay down. If pedal comes up a bit, something is wrong.

G15

47210-G1500 BOOSTER ASSY-BRAKE 9810- <> 47210-G1510 47212-D0100 PACKING-BOOSTER [4-bolt boster-to-firewall gasket] 47471-G1500 HOSE-BOOSTER [from booster to check valve] 47478-03B00 VALVE ASSY-CHECK 47472-95W00 HOSE-BOOSTER [from check valve to intake manifold] 47475-H8504 CONNECTOR-BOOSTER HOSE [intake manifold fitting]

Album 16891 Album 17265 Album 17266